Low tack, and steady
Our lowest tack goes down to ≤1.5 gf/25mm. Silicone-coated film also holds its tack more steadily.
Silicone PET protective film, low tack held precisely.
Silicone adhesive coated on PET film. It pushes out trapped air on its own as you apply it, and peels off with no residue. Tack starts at ≤1.5 gf/25mm and goes up to 280; slit to the width you need.
- Tack ≤1.5 to 280
- gf/25mm (spec sheet)
- Clear
- Blue or antistatic on request (spec sheet)
- 50–100 µm
- Four film gauges, 5 or 10 µm adhesive (spec sheet)
Most buyers come to us for the ultra-low tack.
On low-tack film, our tack varies very little — tighter than most coating plants can hold.
Pushes out the air on its own
Good adhesion, and it keeps the product clean. Single-layer grades wind without bubbles, too.
Peels off with no residue
High cleanliness. It stays on while electronics are processed and while they ship, and when it finally comes off, the surface is clean.
Want the numbers? Open the spec table (tack, film + adhesive, roll width)
| Grade | Tack (gf/25mm) | Film + adhesive (µm) | Roll width (mm) |
|---|---|---|---|
| SH-0501S | ≤1.5 | 50 + 5 | 1250 |
| SH-0500SM | ≤1.5 | 50 + 10 | 980 |
| SH-0700SM | ≤1.5 | 70 + 10 | 1060 |
| SH-0701S | 1.5±1 | 70 + 5 | 1250 / 1080 |
| SH-0701SM | 1.5±1 | 70 + 10 | 980 |
| SH-0501SM | 2±1 | 50 + 10 | 980 |
| SH-0502S | 4±2 | 50 + 5 | 1250 |
| SH-0502SM | 4±2 | 50 + 10 | 980 |
| SH-0702S | 4.5±1.5 | 70 + 5 | 1250 |
| SH-0702SM | 4.5±1.5 | 70 + 10 | 980 |
| SH-0902SM | 4.5±1.5 | 90 + 10 | 1020 |
| SH-1003SM | 5±3 | 100 + 10 | 980 |
| SH-0703S | 6±3 | 70 + 5 | 1250 |
| SH-0503SM | 6±3 | 50 + 10 | 980 |
| SH-0703SM | 6±3 | 70 + 10 | 980 |
| SH-0505SM | 9±3 | 50 + 10 | 980 |
| SH-0505S | 10±3 | 50 + 5 | 1250 |
| SH-0705S | 10±3 | 70 + 5 | 1250 |
| SH-0705SM | 10±3 | 70 + 10 | 980 |
| SH-0506S | 15±5 | 50 + 5 | 1250 / 1320 |
| SH-0706S | 15±5 | 70 + 5 | 1250 |
| SH-0506SM | 15±5 | 50 + 10 | 980 |
| SH-0706SM | 18±5 | 70 + 10 | 980 |
| SH-0507S | 25±5 | 50 + 5 | 1250 |
| SH-0707S | 25±5 | 70 + 5 | 1250 |
| SH-0507SM | 25±5 | 50 + 10 | 980 |
| SH-0707SM | 30±10 | 70 + 10 | 980 |
| SH-1005SM | 30±10 | 100 + 10 | 980 |
| SH-0510SM | 35±8 | 50 + 10 | 980 |
| SH-0710SM | 40±10 | 70 + 10 | 980 |
| SH-0910SM | 40±10 | 90 + 10 | 980 |
| SH-0413S | 60±10 | 50 + 5 | 1150 / 1050 |
| SH-0512SF | 60±18 | 50 + 10 | 1150 |
| SH-0714SM | 70±20 | 70 + 10 | 980 |
| SH-0513S | 100±20 | 50 + 5 | 1050 |
| SH-0513SF | 105±15 | 50 + 10 | 1150 |
| SH-0715SM | 150±50 | 70 + 10 | 980 |
| SH-0717SM | 280±80 | 70 + 10 | 980 |
These are the values on our spec sheet. The sheet doesn't state the test conditions (substrate, peel angle and speed) — tell me if you need them and we'll confirm and send them to you. Rolls are slit to the width you need.
It protects electronics through processing and shipping.
These are the two uses our spec sheet and brochure list.
Converters: in-line die-cutting and waste stripping
You buy roll stock, convert it into die-cut parts and sell them on. The die-cutting page walks through all four steps.
See the die-cutting scenario
Electronics: on during processing, still on at shipping
It leaves the factory with the product and only comes off at your customer's.
Request a free sampleWhat are you putting it on? Tell me, and I'll pick the grade.
“What material does it go on, and what does it need to do? How thick, how wide, how low a tack, antistatic or not? Tell me whatever you know.”
If you have a film you use now, send us a piece — we'll test it first, then match it and aim to do better. I'll reply within 24 hours: leave me a message with the button below, or email me directly.
Email: daodao@siliconefilmtape.com
Daodao Your contact
Want to try a sample? Send it today, hear back within 24 hours.
Samples are free; you cover the freight.
Request a free sample →
Daodao Your contact